Sanjaya, Edi
Department of Physics, Universitas Islam Negeri Syarif Hidayatullah Jakarta, Jalan Ir. H. Juanda 95, Ciputat, Banten 15412, Indonesia

Published : 5 Documents
Articles

Found 5 Documents
Search

A Novel Ternary CoFe2O4/CuO/CoFe2O4 as a Giant Magnetoresistance Sensor Ramli, Ramli; Hartono, Ambran; Sanjaya, Edi; Aminudin, Ahmad; Khairurrijal, Khairurrijal; Haryanto, Freddy; Imawan, Cuk; Djamal, Mitra
Journal of Mathematical and Fundamental Sciences Vol 48, No 3 (2016)
Publisher : ITB Journal Publisher, LPPM ITB

Show Abstract | Original Source | Check in Google Scholar | Full PDF (621.165 KB)

Abstract

This paper reports the results of a study relating to the synthesis of a novel ternary CoFe2O4/CuO/CoFe2O4 thin film as a giant magnetoresistance (GMR) sensor. The CoFe2O4/CuO/CoFe2O4 thin film was prepared onto silicon substrate via DC magnetron sputtering with the targets facing each other. X-ray diffraction was used to determine the structure of the thin film and a 4-point method was used to measure the MR ratio. The GMR ratio is highly dependent on the ferrimagnetic (CoFe2O4) and nonmagnetic (CuO) layer thickness. The maximum GMR ratio at room temperature obtained in the CoFe2O4/CuO/CoFe2O4 thin film was 70% when the CoFe2O4 and the CuO layer had a thickness of 62.5 nm and 14.4 nm respectively.
STRUKTUR MIKRO DAN SIFAT MAGNETIK DARI LAPISAN TIPIS NANOKOMPOSIT Fe3O4/PVDF Ramli, Ramli; Yulfriska, Nidya; Darvina, Yenni; Yulkifli, Yulkifli; Sanjaya, Edi; Hartono, Ambran
Spektra: Jurnal Fisika dan Aplikasinya Vol 3 No 3 (2018): SPEKTRA: Jurnal Fisika dan Aplikasinya, Volume 3 Issue 3, December 2018
Publisher : Program Studi Fisika Universitas Negeri Jakarta

Show Abstract | Original Source | Check in Google Scholar | Full PDF (425.056 KB)

Abstract

Artikel ini berhubungan dengan laporan pembuatan lapisan tipis nanokomposit Fe3O4/PVDF (Poly Vinylidine Fluoride) dengan fraksi berat nanopartikel Fe3O4 yang berbeda. Nanokomposit Fe3O4/PVDF disiapkan menggunakan metode sol-gel dan kemudian ditumbuhkan menggunakan alat spin coating di atas substrat kaca. Lapisan tipis nanokomposit Fe3O4/PVDF dikarakterisasi menggunakan XRD, FTIR, SEM, dan VSM untuk menentukan struktur mikro dan sifat magnetiknya. Fraksi berat nanopartikel Fe3O4 dalam matriks PVDF berpengaruh pada struktur mikro dan sifat magnetik nanokomposit. Hasil karakterisasi XRD dan FTIR menunjukkan bahwa nanokomposit telah terbentuk dan telah terjadi interaksi antara pengisi (Fe3O4) dengan molekul polimer PVDF. Morfologi permukaan nanokomposit memperlihatkan bentuk sperulus (spherulites) dan lamela radial. Analisis kurva histeresis dari nanokomposit Fe3O4/PVDF menunjukkan magnetisasi saturasi dari lapisan nanokomposit Fe3O4/PVDF bertambah dengan bertambahnya konsentrasi Fe3O4 dalam sampel. Pengaruh fraksi Fe3O4 dalam sampel nanokomposit Fe3O4/PVDF terhadap sifat struktur mikro dan sifat magnetik sampel dilaporkan secara rinci dalam artikel ini.
Rancang Bangun Home Automation Berbasis Raspberry Pi 3 Model B dengan Interface Aprlikasi Media Sosial Telegram sebagai Kendali Sedayu, Agung; Yuniarti, Elvan; Sanjaya, Edi
Al-Fiziya: Journal of Materials Science, Geophysics, Instrumentation and Theoretical Physics Vol 1, No 2 (2018)
Publisher : Department of Physics, Faculty of Science and Technology UIN Syarif Hidayatullah Jakarta

Show Abstract | Original Source | Check in Google Scholar | Full PDF (196.253 KB)

Abstract

Telah berkambangnya tekonologi home automation pada zaman ini dan salah satunya dengan pemanfaatan smartphone sebagai salah satu pengendalinya. Pada penelitian ini memanfaatkan sebuah aplikasi media sosial telegram dan sebuah single board computer sebagai kontrol pada sebuah home automation. Penelitian ini bertujuan untuk membangun sebuah home automation dengan menggunakan Raspberry Pi dan aplikasi media sosial telegram sebagai kendalinya. Dengan studi pustaka dan metode eksperimen penelitian ini berhasil merancang bangun sebuah home automation menggunakan Raspberry Pi 3 Model B dengan interface aplikasi telegram sebagai kendalinya. Dibutuhkan sebuah Bot API telegram agar Raspberry Pi dan aplikasi telegram dapat terhubung. Perangkat yang digunakan dalam penelitian ini meliputi: single board computer Raspberry Pi 3 Model B, 2 buah relay untuk 2 perangkat elektronik (lampu dan kipas), 1 buah MCB dan smartphone yang telah terinstall aplikasi telegram yang digunakan sebagai pengontrol perangkat elektronik. Hasil dari penelitian ini sudah sesuai dengan tujuannya yaitu merancang bangun sebuah home automation dengan menggunakan Raspberry Pi dan aplikasi media social telegram sebagai kendalinya mensimulasikannya pada peralatan elektronika.
Pembuatan dan Karakterisasi Keramik Magnet BaFe12O19 dengan Variasi Waktu Milling dan Temperatur Sintering Salam, Syaiful Izzuddin; Sanjaya, Edi; Muljadi, Muljadi
Al-Fiziya: Journal of Materials Science, Geophysics, Instrumentation and Theoretical Physics Vol 2, No 1 (2019)
Publisher : Department of Physics, Faculty of Science and Technology UIN Syarif Hidayatullah Jakarta

Show Abstract | Original Source | Check in Google Scholar | Full PDF (197.372 KB)

Abstract

In this study, we made ceramic magnet of barium hexaferrite (BaFe12O19) with variation of milling time and sintering temperature by powder metallurgy method. First, barium hexaferrite powder mashed with a rotary ball mill. Milling is done with medium of water (wet milling) for 4 hours and 12 hours. Then, the sample is dried for 24 hours and printed with a load of 8 tons for 1 minute. Then, the pellet-shaped sample sintered at a temperature of 1100 °C and 1200 °C with a holding time of 1 hour. The density and porosity measurements were carried out using the Archimedes Method, phase analysis with XRD, and magnetic flux density using gaussmeter. The highest density were found in samples that were milled for 12 hours and sintered at the temperature of 1200 °C ie 4.495 gr/cm3. In that sample also obtained the lowest porosity  0.89%. From XRD analysis, we knew that hematite (Fe2O3) was found as impurity phase. From gaussmeter, the samples with the highest magnetic flux density were found in samples that were milled for 4 hours and sintered at a temperature of 1200 °C ie 410.3 G.
FABRICATION AND CHARACTERIZATION OF THE COMPOSITES OF RESIN – HUSK OF RICE AND RESIN - RUB ASH Pattersons, Muhammad Lawrence; Naripa, Arin; Winarno, Sendiko Janu; Abhan, Siti Mawaddah; Sanjaya, Edi
Spektra: Jurnal Fisika dan Aplikasinya Vol 3 No 2 (2018): SPEKTRA: Jurnal Fisika dan Aplikasinya, Volume 3 Issue 2, August 2018
Publisher : Program Studi Fisika Universitas Negeri Jakarta

Show Abstract | Original Source | Check in Google Scholar | Full PDF (329.608 KB)

Abstract

We have done the fabrication of two kinds of composite material the fillers that we used rub ash for one type of composite and the husk of rice for another, the matrix for both is resin. The resin – rub ash composite, the volume ratio of filler and matrix is 1:1, while in the resin – husk of rice composite we used three volume ratios, those are 1:1, 1:2, and 2:1. After the process of fabrication was done, we did TGA test and three points flexural test for every composite we fabricated. The results of TGA test show that the most significant weight decrease of resin – rub ash composite occurred at 390,29 ºC, while the resin – rub ash composite's most considerable weight decrease occurred at 399,86 ºC. The results of three points flexural test show that elasticity of resin – rub ash composite is 4,97 x 109 N/m2, while elasticity modulus of all kinds of the resin – husk of rice composite is in order of 108 N.m2 and 106 N/m2. Overall, we can conclude that the resin – husk of rice composite is more heatproof and more elastic than the resin – rub ash composite. Keywords: composite, resin, rub ash, the husk of rice.